GRIPiTe®C60 SD Contact Adhesive is a powerful solvent-free two-way stick static dissipative adhesive.  GRIPiTe®C60 SD Contact is available in 5kg and 20kg buckets. 

GRIPiTe®C60 SD Contact Adhesive has a short open time with bonding capabilities for Vinyl Wall  Cladding, Skirtings, profi les and floor coverings on absorbent and non-absorbent substrates internally.  GRIPiTe®C60 SD, is suitable for use with the installation of: 

• PVC or Vinyl Flooring, 
• Linoleum, 
• LVT’s, 
• Rubber Flooring, 
• Needle Punch Carpeting and most floor and wall coverings. 
• Is safe to use on many materials, including polystyrene and solvent-sensitive products. 
• Should you be unsure as to the material and adhesive to utilise in your application please consult with the iTe Products technical team.  
• GRIPiTe®C60 SD Has a low odour, making it suitable for use in rooms adjacent to occupied areas. 
• GRIPiTe®C60 SD is Water-based, with no organic solvents, this adhesive is “green” and complies with all GBCSA requirements. 

• GRIPiTe®C60 SD Contact Adhesive functions when the two pre-adhered surfaces have flashed off,  leaving tacky but dry adhesive films on them.  
• Care must be taken to allow the adhesive films to dry sufficiently to prevent entrapment of any water from the adhesive between the surfaces, which will retard the curing and final bond strength. • Atmospheric conditions will influence fl ash off times and as such time to fl ash off may vary  • ensure no building dust and debris contaminates the adhesive film as this will affect adhesion properties as well as mirror through the floor covering. 
• Use a mohair or foam roller to apply the adhesive in a thin, fi ne even layer onto each surface, and wait for the two surfaces to dry.  
• When dry, line up the material to be bonded carefully, and place the material into the adhesive,  rubbing it into position to ensure no air entrapment.  
• When finally positioned, rub the surface entirely, bring pressure to bear to promote the best possible bond. 
• NB The floor temperature must be maintained constantly above 10°c during and after the application,  flash off and final drying of the adhesive. The floor temperature must not deviate more than 19°c  from the Initial temperature reading during Installation 
• NB When the two adhesive-applied surfaces are brought together, subsequent movement of the sheeting or material is NOT possible. It is important to line the material up correctly before bringing the surfaces into contact with one another as movement may lift adhesive causing failure. 

• When fixing materials to substrates other than cementitious screeds or substrates, please consult with iTe Products’ technical staff. 

GRIPiTe®C60 SD Contact is applied onto both surfaces with a mohair roller. This method yields approximately 6m² per Litre. (covering both surfaces) 

For extrusions or small profiles, a brush application is preferable to ensure that sufficient adhesive is present to bridge the two surfaces. This method yields approximately 6m² per Litre. (covering both  surfaces)  

On very porous substrates it is advisable to apply sufficient adhesive to prevent glue-line starvation by using a lamb’s wool roller, or priming the surface with a coat of GRIPiTe®C60 first.

RIPiTe®C60 SD must be stored in a cool dry place. 

GRIPiTe®C60 SD must be stored between 5°c and 30°c, and protected from frost, direct sunlight and the  elements. 

GRIPiTe®C60 SD will last for 12 months unopened.

• Ensure the covering is properly acclimatised prior to Installation, as per covering manufacturers recommendations, and installation instructions prior to use.  
• Ensure a stable ambient temperature is maintained for a minimum of 24 hours pre, during and post  Installation to allow the adhesive to fully cure and minimise any expansion and shrinkage within the covering material.  
• Allow the adhesive 24 hours to set before applying any load to the covering, this Includes but is not limited to furniture.

Safety goggles and gloves should be worn to protect the eyes and skin from accidental exposure. In the event of eye contamination, the eyes must immediately be washed out with copious amounts of clean water, and medical assistance sought. 

It is recommended that overalls be worn to minimise soiling of clothing.