GRIPiTe®V30 SD has conductive properties which enable the discharge or dissipation of electrical charges which build up in vinyl flooring to a discharge earth leakage point. 

GRIPiTe®V30 SD is a single component adhesive supplied in 5l and 20l drums and is clearly labelled GRIPiTe®V30 SD, is suitable for use with the installation of: 

• semi-fl exible vinyl tiles onto cement-based substrates. 
• fully flexible vinyl tiles onto cement-based substrates.  
• Vinyl Sheeting onto cement-based substrates. 
• Unbacked carpet tiles onto cement-based substrates. 
• Should you be unsure as to the material and adhesive to utilise in your application please consult  with the ITe Products technical team.  

GRIPiTe®V30 SD Has a low odour, making it suitable for use in rooms adjacent to occupied areas. GRIPiTe®V30 SD is Water-based, with no organic solvents, this adhesive is “green” and complies with all  GBCSA requirements. 

• GRIPiTe®V30 SD is poured onto the floor and evenly spread with the A2 notched trowel. • the notched trowel must be held perpendicular to the floor surface to ensure the correct volume of adhesive is applied.  
• In order to prevent adhesive trowel marks to be visible once the adhesive has set under the flooring,  the wet adhesive may be rolled with a mohair roller to flatten the ridges. Care must be taken to ensure that adhesive transfer still takes place. 
• GRIPiTe®V30 SD must be allowed to flash off and develop its tack which happens approximately  10min after application.  
• Atmospheric conditions will influence flash off times and as such time to fl ash off may vary  • Ensure no building dust and debris contaminates the adhesive film as this will affect adhesion  properties as well as mirror through the floor covering  
• At this point the floor covering is laid into the adhesive following the floor covering manufacturers installation instructions.  
• allow sufficient transfer onto the back of the floor covering (If the floor covering is laid in too late insufficient transfer occurs, and the adhesion is compromised and weak). If the floor covering is laid to early adhesive may push between the gaps and cause inadequate adhesion.  
• Lay the floor covering into the adhesive pushing from the centre towards the ends to ensure any air trapped between covering and substrate is removed and ensuring full contact is made between adhesive and floor covering.  
• Roll the floor covering utilising a 68kg heavy roller in a north, south and then east, west fashion to maximise transfer and flatten the adhesive ridge lines.  
• Re-roll the surface utilising the 68kg heavy roller once the installation is completed and or if required to ensure full contact is achieved.  
• NB The floor temperature must be maintained constantly above 10°c during and after the application,  flash off and final drying of the adhesive. The floor temperature must not deviate more than 15°c  from the Initial temperature reading during installation.

• Ensure the floor covering is properly acclimatised prior to Installation, as per floor covering manufacturers recommendations, and installation instructions prior to use.  
• Ensure a stable ambient temperature is maintained for a minimum of 24 hours pre, during and post  Installation to allow the adhesive to fully cure and minimise any expansion and shrinkage within the floor covering material.  
• Allow the adhesive 24 hours to set before applying any load to the floor covering, this Includes but is not limited to furniture. 
• The use of chair protectors is strongly recommended to minimise ware on the entire flooring system.
• Walkoff mats are also recommended to minimise soiling of the floor covering.  

GRIPiTe®V30 SD must be stored in a cool dry place. 

GRIPiTe®V30 SD must be stored between 5°c and 30°c, and protected from frost, direct sunlight and the  elements. 

GRIPiTe®V30 SD will last for 12 months unopened.

GRIPiTe®V30 SD has an approximate spread rate of 4m²/litre when applied using the A2 notched trowel,  on a LEVELiTe® surface.  

• The life span of the notched trowel greatly impacts the volume of adhesive applied to the substrate and should therefore not be modified or tampered with in any way. Failure to adhere to this may result in nullification of guarantees issued by iTe Products.  

• The notch has a life span of approximately 50²m per side (if supplied by iTe Products®)